Refine
H-BRS Bibliography
- yes (36)
Departments, institutes and facilities
- Fachbereich Informatik (36) (remove)
Document Type
- Conference Object (18)
- Article (12)
- Part of a Book (2)
- Patent (2)
- Report (2)
Year of publication
Keywords
- Skin detection (2)
- automated sensor-screening (2)
- biometrics (2)
- machine learning (2)
- optical sensor (2)
- semiconducting metal oxide gas sensor array (2)
- Circular saws (1)
- Collaborating industrial robots (1)
- Embedded system (1)
- Exergame (1)
In the presented project, a new approach for the prevention of hand movements leading to hazards and for non-contact detection of fingers is intended to permit comprehensive and economical protection on circular saws. The basic principles may also be applied to other machines with manual loading and / or unloading. With an automatic blade guard an improved integration of the protection system can be achieved. In addition a new detection principle is explained. The distinction between skin and wood or other material is achieved by a dedicated spectral analysis in the near infrared region. Using LED and photodiodes it is possible to detect fingers and hands reliably. With a kind of light curtain the intrusion of hands or fingers into the dangerous zone near the blade guard can be prevented.
The simultaneous operation of multiple different semiconducting metal oxide (MOX) gas sensors is demanding for the readout circuitry. The challenge results from the strongly varying signal intensities of the various sensor types to the target gas. While some sensors change their resistance only slightly, other types can react with a resistive change over a range of several decades. Therefore, a suitable readout circuit has to be able to capture all these resistive variations, requiring it to have a very large dynamic range. This work presents a compact embedded system that provides a full, high range input interface (readout and heater management) for MOX sensor operation. The system is modular and consists of a central mainboard that holds up to eight sensor-modules, each capable of supporting up to two MOX sensors, therefore supporting a total maximum of 16 different sensors. Its wide input range is archived using the resistance-to-time measurement method. The system is solely built with commercial off-the-shelf components and tested over a range spanning from 100Ω to 5 GΩ (9.7 decades) with an average measurement error of 0.27% and a maximum error of 2.11%. The heater management uses a well-tested power-circuit and supports multiple modes of operation, hence enabling the system to be used in highly automated measurement applications. The experimental part of this work presents the results of an exemplary screening of 16 sensors, which was performed to evaluate the system’s performance.
The following work presents algorithms for semi-automatic validation, feature extraction and ranking of time series measurements acquired from MOX gas sensors. Semi-automatic measurement validation is accomplished by extending established curve similarity algorithms with a slope-based signature calculation. Furthermore, a feature-based ranking metric is introduced. It allows for individual prioritization of each feature and can be used to find the best performing sensors regarding multiple research questions. Finally, the functionality of the algorithms, as well as the developed software suite, are demonstrated with an exemplary scenario, illustrating how to find the most power-efficient MOX gas sensor in a data set collected during an extensive screening consisting of 16,320 measurements, all taken with different sensors at various temperatures and analytes.
In the presented project, new approaches for the prevention of hand movements leading to hazards and for non-contact detection of fingers are intended to permit comprehensive and economical protection on circular saws. The basic principles may also be applied to other machines with manual loading and/or unloading. Two new detection principles are explained. The first is the distinction between skin and wood or other material by spectral analysis in the near infrared region. Using LED and photodiodes it is possible to detect fingers and hands reliable. With a kind of light curtain the intrusion into the dangerous zone near the blade can be prevented. The second principle is video image processing to detect persons, arms and fingers. In the first stage of development the detection of upper limb extremities within a defined hazard area by means of a computer based video image analysis is investigated.
Mobile Datenkommunikation basiert üblicherweise auf der drahtlosen Anbindung eines Endgerätes an eine Basisstation, die ihrerseits an eine feste Infrastruktur angebunden ist. In vielen Szenarien sind diese Voraussetzungen jedoch nicht gegeben. Beispiele hierfür sind Katastrophen wie Hochwasser, Erdbeben oder Flugzeugabstürze in dünn besiedelten Regionen. Einen Lösungsansatz für sich daraus ergebende Anforderungen bieten dynamisch aufgebaute Ad-Hoc Netze mit einer satellitengestützten Anbindung an eine Festnetz-Infrastruktur. In solchen Netzen stellen die mobilen Terminals die benötigte lokale Infrastruktur selbst dynamisch her. Ziel der hier vorgestellten Arbeiten ist es, die Zuverlässigkeit und Dienstqualität der verwendeten Technologien zu untersuchen und durch geeignete Mechanismen so anzupassen, dass die Anforderungen typischer Applikationen möglichst erfüllt werden. Zur Demonstration wurde ein Prototyp aufgebaut, der unter anderem die Anwendungen "Voice over IP" (VoIP), "Datenbankzugriff im Intranet" und "Internetzugang" (WWW) untersucht.
Vorrichtung zur Authentifikation einer Person anhand mindestens eines biometrischen Parameters
(2008)
Die Vorrichtung zur Authentifikation einer Person anhand mindestens eines biometrischen Parameters, insbesondere anhand eines Fingerabdrucks, ist versehen mit einem Biometrie-Detektor (20) zur Detektion eines biometrischen Parameters, einem Haut-Detektor (24) zur berührungslosen Erkennung lebender menschlicher Haut innerhalb eines Erfassungsbereichs. Der Haut-Detektor (24) weist mindestens eine Gruppe aus mindestens einer Strahlungseinheit (26, 28) und mindestens einer Empfangseinheit (30) auf. Die mindestens eine Strahlungseinheit (26, 28) gibt in Richtung auf den Erfassungsbereich Strahlung bei mindestens zwei unterschiedlichen Wellenlängen im Wellenlängenbereich zwischen 400 nm und 1500 nm ab, wobei mindestens eine der Wellenlängen (26, 28) im Wellenlängenbereich von 900 nm bis 1500 nm liegt und die mindestens eine Empfangseinheit (30) aus dem Erfassungsbereich reflektierte Strahlung empfängt. Ferner ist die Vorrichtung versehen mit einer mit dem Biometer-Detektor (20) und dem Haut-Detektor (24) verbundenen Signalauswerteeinheit (22) zur Auswertung der Intensität der von der Empfangseinheit (30) empfangenen reflektierten Strahlungen der Strahlungseinheit (26, 28). In der Signalauswerteeinheit (22) ist anhand der Intensitäten der von der Empfangseinheit (30) empfangenen reflektierten Strahlungen der Strahlungseinheit (26, 28) bei den zwei unterschiedlichen Wellenlängen ermittelbar, ob der Haut-Detektor lebende menschliche Haut erkennt.
This paper presents recent research on an active multispectral scanning sensor capable of classifying an object's surface material in order to distinguish between different kinds of materials and human skin. The sensor itself has already been presented in previous work and can be used in conjunction with safeguarding equipment at manually-fed machines or robot workplaces, for example. This work shows how an extended sensor system with advanced material classifiers can be used to provide additional value by distinguishing different materials of work pieces in order to suggest different tools or parameters for the machine (e.g. the use of a different saw blade or rotation speed at table saws). Additionally, a first implementation and evaluation of an active multispectral camera system addressing new safety applications is described. Both approaches intend to increase the productivity and the user's acceptance of the sensor technology.
Diese Arbeit präsentiert eine Methode zur zuverlässigen Personendetektion für die Absicherung des Arbeitsbereichs von Industrierobotern. Hierzu wird ein im Nahinfrarotbereich (NIR) arbeitendes aktives Kamerasystem eingesetzt, das durch erweiterte und robuste Hauterkennungseigenschaften besonders dazu geeignet ist, zwischen verschiedensten Materialoberflächen und menschlicher Haut zu unterscheiden. So soll zum einen die Erkennungsleistung gegenüber handelsüblichen, im visuellen Bereich arbeitenden RGB-Kamerasystemen gesteigert werden und gleichzeitig eine „intelligente“ Form des Mutings realisiert werden. Die im Rahmen des Projekts „Sichere Personendetektion im Arbeitsbereich von Industrierobotern durch ein aktives NIR-Kamerasystem (SPAI)“ entwickelte und hier vorgestellte Methode erreicht in einer ersten Variante eine pixelweise Personenerkennungsrate von ca. 98,16%.
The choice of suitable semiconducting metal oxide (MOX) gas sensors for the detection of a specific gas or gas mixture is time-consuming since the sensor’s sensitivity needs to be characterized at multiple temperatures to find its optimal operating conditions. To obtain reliable measurement results, it is very important that the power for the sensor’s integrated heater is stable, regulated and error-free (or error-tolerant). Especially the error-free requirement can be only be achieved if the power supply implements failure-avoiding and failure-detection methods. The biggest challenge is deriving multiple different voltages from a common supply in an efficient way while keeping the system as small and lightweight as possible. This work presents a reliable, compact, embedded system that addresses the power supply requirements for fully automated simultaneous sensor characterization for up to 16 sensors at multiple temperatures. The system implements efficient (avg. 83.3% efficiency) voltage conversion with low ripple output (<32 mV) and supports static or temperature-cycled heating modes. Voltage and current of each channel are constantly monitored and regulated to guarantee reliable operation. To evaluate the proposed design, 16 sensors were screened. The results are shown in the experimental part of this work.