Refine
H-BRS Bibliography
- yes (39) (remove)
Departments, institutes and facilities
- Institut für Technik, Ressourcenschonung und Energieeffizienz (TREE) (39) (remove)
Document Type
- Conference Object (25)
- Article (9)
- Book (monograph, edited volume) (1)
- Doctoral Thesis (1)
- Lecture (1)
- Preprint (1)
- Report (1)
Year of publication
- 2015 (39) (remove)
Keywords
- Prozessmanagement (2)
- Prozessorganisation (2)
- AMBER (1)
- Competition (1)
- Compositional Pattern Producing Networks (1)
- DC electric drives (1)
- Degree of conversion (1)
- Dental resin (1)
- Design Optimization (1)
- Engineering (1)
Solar energy is one option to serve the rising global energy demand with low environmental Impact [1]. Building an energy system with a considerable share of solar power requires long-term investment and a careful investigation of potential sites. Therefore, understanding the impacts from varying regionally and locally determined meteorological conditions on solar energy production will influence energy yield projections. Clouds are moving on a short term timescale and have a high influence on the available solar radiation, as they absorb, reflect and scatter parts of the incoming light [2]. However, modeling photovoltaic (PV) power yields with a spectral resolution and local cloud information gives new insights on the atmospheric impact on solar energy.
Ultra-fast photopolymerization of experimental composites: DEA and FT-NIRS measurement comparison
(2015)
Work in progress: Starter-project for first semester students to survey their engineering studies
(2015)
In this doctoral thesis the curing process of visible light-curing (VLC) dental composites and 3D printing rapid prototyping (RP) materials are investigated with the focus on dielectric analysis (DEA). This method is able to monitor the curing of resins in an alternating electric fringe field with adjustable frequencies and is often used for cure control of composites manufacturing in the aviation and automotive industry but hardly established in dental science or RP method development. It is capable of investigating very fast initiation and primary curing processes using high frequencies in the kHz-range. The aim of the Thesis is a better understanding of the curing processes with respect to curing parameters such as resin composition, viscosity, temperature, and for light-curing composites also light intensity and irradiation depth. Due to the nature of both dental and RP systems an application of specific experimental set-up had to be designed allowing for the generation of reproducible and valid results. Subsequently, different evaluation methods were developed to characterize the curing behavior of both material types. A special focus was paid to the determination of kinetic parameters from DEA measurements. Reaction rates of the curing of the corresponding thermosets were calculated and applied to the ion viscosity curves measured by DEA to evaluate reaction kinetic parameters. For the dental composites it could be clearly shown that the initial curing rate is directly proportional to light intensity and not to its square root as proposed by many others authors. A good description of the curing behaviour of 3DP RP materials was also achieved assuming a reaction order smaller than one. This data provides the base for the kinetic modeling of polymerization and curing processes proposed within the Thesis.
This paper proposes a new artificial neural network-based maximum power point tracker for photovoltaic application. This tracker significantly improves efficiency of the photovoltaic system with series-connection of photovoltaic modules in non-uniform irradiance on photovoltaic array surfaces. The artificial neural network uses irradiance and temperature sensors to generate the maximum power point reference voltage and employ a classical perturb and observe searching algorithm. The structure of the artificial neural network was obtained by numerical modelling using Matlab/Simulink. The artificial neural network was trained using Bayesian regularisation back-propagation algorithms and demonstrated a good prediction of the maximum power point. Relative number of Vmpp prediction errors in range of ±0.2V is 0.05% based on validation data.
Polyether and polyether/ester based TPU (thermoplastic polyurethanes) were investigated with wide-angle XRD (X-ray diffraction) and SAXS (small angle X-ray scattering). Furthermore, SAXS measurements were performed in the temperature range of 30 °C to 130 °C. Polyether based polymers exhibit only one broad diffraction signal in a region of 2 θ 15° to 25°. In case of polyurethanes with ether/ester modification, the broad diffraction signal arises with small sharp diffraction signals. SAXS measurements of polymers reveal the size and shape of the crystalline zones of the polymer. Between 30 °C and 130 °C the size of the crystalline zone changes significantly. The size decreases in most of investigated TPU. In the case of Desmopan 9365D an increase of the particle size was observed.