Open Access

The autocatalyzed ethanolic organosolv process is gaining increasing attention for the sulfur-free isolation of lignin, which is subsequently used as a renewable substitute for various fossil-based applications. For the first time, the mechanochemical influence of seven different particle sizes of two different biomasses on the respective organosolv lignin structure is examined. Wine pruning (Pinot Noir) and wine pomace (Accent) are used for organosolv process with particle sizes ranging from 2.0–1.6 mm to less than 0.25 mm. As particle size decreases, the weight-average molecular weight increases, while the total phenol content decreases significantly. Additionally, the distribution of the lignin-typical monolignols and relevant substructures, as determined by two-dimensional heteronuclear nuclear magnetic resonance spectra single quantum coherence (HSQC), is observed. The degree of grinding of the biomass has a clear chemical–structural influence on the isolated HG and HGS organosolv lignins. Therefore, it is crucial to understand this influence to apply organosolv lignins in a targeted manner. In the future, particle size specifications in the context of the organosolv process should be expressed in terms of distribution densities rather than in terms of a smaller than specification.

In the coming years, the European Union plans to establish Proton Exchange Membrane (PEM) electrolyzers, each with a 100 MW capacity. However, the selection of their locations has not been systematically optimized to leverage potential benefits, such as utilizing waste heat from large facilities for district heating. Presently, there are hardly any corresponding system models in the literature dynamically simulating a PEM electrolyzer of this size. This paper introduces a first model approach for such systems, drawing on parameters from existing literature. It addresses the inconsistency found in the literature regarding the use of the exchange current density, which varies by a factor of . A novel optimization process is developed by using an auxiliary parameter to fit the exchange current density with a newfound condition between the anode and cathode side. The outcome is a comprehensive model of a PEM electrolyzer plant, exemplarily adapted to the Siemens Silyzer 300.

The transport sector is a major source of air pollution and thus a major contributor to the changing climate. As a result, in the recent past, driving bans have been imposed on cars with critical pollutant groups. As an international UN campus and self-proclaimed climate capital, the Federal City of Bonn declared a climate emergency in 2019 and participated in a federally funded “Lead City” project to optimise air quality. A key goal of the project is to reduce private motorised transport and strengthen public transport. Among the implemented measures, a “climate ticket” was introduced in 2019 whereby consumers could purchase an annual 365 € ticket for all local public transport. This paper reports on an analysis of that ticket’s changes in travel behavior. A quantitative survey (n = 1,315) of the climate ticket users as well as the multiple regressions confirm that the climate ticket attracted more customers to the buses and trams and that a modal shift for the period of the measure was recognisable. The multiple regressions showed that the ticket was perceived significantly more positively by full-time employed users than by unemployed people. The results also show that, in addition to the price, it is essential that travel time and reliability are ensured. Furthermore, the eligible groups of people, the area of coverage, and good connecting services should be extended. To sustainably improve air quality, this type of mobility service must be optimised and introduced on a permanent basis.

Electrical signal transmission in power electronic devices takes place through high-purity aluminum bonding wires. Cyclic mechanical and thermal stresses during operation lead to fatigue loads, resulting in premature failure of the wires, which cannot be reliably predicted. The following work presents two fatigue lifetime models calibrated and validated based on experimental fatigue results of an aluminum bonding wire and subsequently transferred and applied to other wire types. The lifetime modeling of Wöhler curves for different load ratios shows good but limited applicability for the linear model. The model can only be applied above 10,000 cycles and within the investigated load range of R = 0.1 to R = 0.7. The nonlinear model shows very good agreement between model prediction and experimental results over the entire investigated cycle range. Furthermore, the predicted Smith diagram is not only consistent in the investigated load range but also in the extrapolated load range from R = −1.0 to R = 0.8. A transfer of both model approaches to other wire types by using their tensile strengths can be implemented as well, although the nonlinear model is more suitable since it covers the entire load and cycle range.

When optimizing the process parameters of the acidic ethanolic organosolv process, the aim is usually to maximize the delignification and/or lignin purity. However, process parameters such as temperature, time, ethanol and catalyst concentration, respectively, can also be used to vary the structural properties of the obtained organosolv lignin, including the molecular weight and the ratio of aliphatic versus phenolic hydroxyl groups, among others. This review particularly focuses on these influencing factors and establishes a trend analysis between the variation of the process parameters and the effect on lignin structure. Especially when larger data sets are available, as for process temperature and time, correlations between the distribution of depolymerization and condensation reactions are found, which allow direct conclusions on the proportion of lignin's structural features, independent of the diversity of the biomass used. The newfound insights gained from this review can be used to tailor organosolv lignins isolated for a specific application.

Monitoring the content of dissolved ozone in purified water is often mandatory to ensure the appropriate levels of disinfection and sanitization. However, quantification bears challenges as colorimetric assays require laborious off-line analysis, while commercially available instruments for electrochemical process analysis are expensive and often lack the possibility for miniaturization and discretionary installation. In this study, potentiometric ionic polymer metal composite (IPMC) sensors for the determination of dissolved ozone in ultrapure water (UPW) systems are presented. Commercially available polymer electrolyte membranes are treated via an impregnation-reduction method to obtain nanostructured platinum layers. By applying 25 different synthesis conditions, layer thicknesses of 2.2 to 12.6 µm are obtained. Supporting radiographic analyses indicate that the platinum concentration of the impregnation solution has the highest influence on the obtained metal loading. The sensor response behavior is explained by a Langmuir pseudo-isotherm model and allows the quantification of dissolved ozone to trace levels of less than 10 µg L−1. Additional statistical evaluations show that the expected Pt loading and radiographic blackening levels can be predicted with high accuracy and significance (R2adj. > 0.90, p < 10−10) solely from given synthesis conditions.

This research studies in detail four different assays, namely DPPH (2,2-diphenyl-1-picrylhydrazyl), ABTS (2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid)), FRAP (ferric ion reducing antioxidant potential) and FC (Folin-Ciocalteu), to determine the antioxidant capacity of standard substances as well as 50 organosolv lignins, and two kraft lignins. The coefficient of variation was determined for each method and was lowest for ABTS and highest for DPPH. The best correlation was found for FRAP and FC, which both rely on a single electron transfer mechanism. A good correlation between ABTS, FRAP and FC, respectively, could be observed, even though ABTS relies on a more complex reaction mechanism. The DPPH assay merely correlates with the others, implying that it reflects different antioxidative attributes due to a different reaction mechanism. Lignins obtained from paulownia and silphium have been investigated for the first time regarding their antioxidant capacity. Paulownia lignin is in the same range as beech wood lignin, while silphium lignin resembles wheat straw lignin. Miscanthus lignin is an exception from the grass lignins and possesses a significantly higher antioxidant capacity. All lignins possess a good antioxidant capacity and thus are promising candidates for various applications, e. g. as additives in food packaging or for biomedical purposes.

This study investigates the initial stage of the thermo-mechanical crystallization behavior for uni- and biaxially stretched polyethylene. The models are based on a mesoscale molecular dynamics approach. We take constraints that occur in real-life polymer processing into account, especially with respect to the blowing stage of the extrusion blow-molding process. For this purpose, we deform our systems using a wide range of stretching levels before they are quenched. We discuss the effects of the stretching procedures on the micro-mechanical state of the systems, characterized by entanglement behavior and nematic ordering of chain segments. For the cooling stage, we use two different approaches which allow for free or hindered shrinkage, respectively. During cooling, crystallization kinetics are monitored: We precisely evaluate how the interplay of chain length, temperature, local entanglements and orientation of chain segments influence crystallization behavior. Our models reveal that the main stretching direction dominates microscopic states of the different systems. We are able to show that crystallization mainly depends on the (dis-)entanglement behavior. Nematic ordering plays a secondary role.

As the identification of microorganisms becomes more significant in industry, so does the utilization of microspectroscopy and the development of effective chemometric models for data analysis and classification. Since only microorganisms cultivated under laboratory conditions can be identified, but they are exposed to a variety of stress factors, such as temperature differences, there is a demand for a method that can take these stress factors and the associated reactions of the bacteria into account. Therefore, bacterial stress reactions to lifetime conditions (regular treatment, 25 °C, HCl, 2-propanol, NaOH) and sampling conditions (cold sampling, desiccation, heat drying) were induced to explore the effects on Raman spectra in order to improve the chemometric models. As a result, in this study nine food-relevant bacteria were exposed to seven stress conditions in addition to routine cultivation as a control. Spectral alterations in lipids, polysaccharides, nucleic acids, and proteins were observed when compared to normal growth circumstances without stresses. Regardless of the involvement of several stress factors and storage times, a model for differentiating the analyzed microorganisms from genus down to strain level was developed. Classification of the independent training dataset at genus and species level for Escherichia coli and at strain level for the other food relevant microorganisms showed a classification rate of 97.6%.

With the increasing demand for ultrapure water in the pharmaceutical and semiconductor industry, the need for precise measuring instruments for those applications is also growing. One critical parameter of water quality is the amount of total organic carbon (TOC). This work presents a system that uses the advantage of the increased oxidation power achieved with UV/O3 advanced oxidation process (AOP) for TOC measurement in combination with a significant miniaturization compared to the state of the art. The miniaturization is achieved by using polymer-electrolyte membrane (PEM) electrolysis cells for ozone generation in combination with UV-LEDs for irradiation of the measuring solution, as both components are significantly smaller than standard equipment. Conductivity measurement after oxidation is the measuring principle and measurements were carried out in the TOC range between 10 and 1000 ppb TOC. The suitability of the system for TOC measurement is demonstrated using the oxidation by ozonation combined with UV irradiation of defined concentrations of isopropyl alcohol (IPA).

(1) Background: Autologous bone is supposed to contain vital cells that might improve the osseointegration of dental implants. The aim of this study was to investigate particulate and filtered bone chips collected during oral surgery intervention with respect to their osteogenic potential and the extent of microbial contamination to evaluate its usefulness for jawbone reconstruction prior to implant placement. (2) Methods: Cortical and cortical-cancellous bone chip samples of 84 patients were collected. The stem cell character of outgrowing cells was characterized by expression of CD73, CD90 and CD105, followed by osteogenic differentiation. The degree of bacterial contamination was determined by Gram staining, catalase and oxidase tests and tests to evaluate the genera of the found bacteria (3) Results: Pre-surgical antibiotic treatment of the patients significantly increased viability of the collected bone chip cells. No significant difference in plasticity was observed between cells isolated from the cortical and cortical-cancellous bone chip samples. Thus, both types of bone tissue can be used for jawbone reconstruction. The osteogenic differentiation was independent of the quantity and quality of the detected microorganisms, which comprise the most common bacteria in the oral cavity. (4) Discussion: This study shows that the quality of bone chip-derived stem cells is independent of the donor site and the extent of present common microorganisms, highlighting autologous bone tissue, assessable without additional surgical intervention for the patient, as a useful material for dental implantology.

Background: Since presenteeism is related to numerous negative health and work-related effects, measures are required to reduce it. There are initial indications that how an organization deals with health has a decisive influence on employees’ presenteeism behavior. Aims: The concept of health-promoting collaboration was developed on the basis of these indications. As an extension of healthy leadership it includes not only the leader but also co-workers. In modern forms of collaboration, leaders cannot be assigned sole responsibility for employees’ health, since the leader is often hardly visible (digital leadership) or there is no longer a clear leader (shared leadership). The study examines the concept of health-promoting collaboration in relation to presenteeism. Relationships between health-promoting collaboration, well-being and work ability are also in focus, regarding presenteeism as a mediator. Methods: The data comprise the findings of a quantitative survey of 308 employees at a German university of applied sciences. Correlation and mediator analyses were conducted. Results: The results show a significant negative relationship between health-promoting collaboration and presenteeism. Significant positive relationships were found between health-promoting collaboration and both well-being and work ability. Presenteeism was identified as a mediator of these relationships. Conclusion: The relevance of health-promoting collaboration in reducing presenteeism was demonstrated and various starting points for practice were proposed. Future studies should investigate further this newly developed concept in relation to presenteeism.

The molecular weight properties of lignins are one of the key elements that need to be analyzed for a successful industrial application of these promising biopolymers. In this study, the use of 1H NMR as well as diffusion-ordered spectroscopy (DOSY NMR), combined with multivariate regression methods, was investigated for the determination of the molecular weight (Mw and Mn) and the polydispersity of organosolv lignins (n = 53, Miscanthus x giganteus, Paulownia tomentosa, and Silphium perfoliatum). The suitability of the models was demonstrated by cross validation (CV) as well as by an independent validation set of samples from different biomass origins (beech wood and wheat straw). CV errors of ca. 7–9 and 14–16% were achieved for all parameters with the models from the 1H NMR spectra and the DOSY NMR data, respectively. The prediction errors for the validation samples were in a similar range for the partial least squares model from the 1H NMR data and for a multiple linear regression using the DOSY NMR data. The results indicate the usefulness of NMR measurements combined with multivariate regression methods as a potential alternative to more time-consuming methods such as gel permeation chromatography.

Because the robust and rapid determination of spoilage microorganisms is becoming increasingly important in industry, the use of IR microspectroscopy, and the establishment of robust and versatile chemometric models for data processing and classification, is gaining importance. To further improve the chemometric models, bacterial stress responses were induced, to study the effect on the IR spectra and to improve the chemometric model. Thus, in this work, nine important food-relevant microorganisms were subjected to eight stress conditions, besides the regular culturing as a reference. Spectral changes compared to normal growth conditions without stressors were found in the spectral regions of 900–1500 cm−1 and 1500–1700 cm−1. These differences might stem from changes in the protein secondary structure, exopolymer production, and concentration of nucleic acids, lipids, and polysaccharides. As a result, a model for the discrimination of the studied microorganisms at the genus, species and strain level was established, with an accuracy of 96.6%. This was achieved despite the inclusion of various stress conditions and times after incubation of the bacteria. In addition, a model was developed for each individual microorganism, to separate each stress condition or regular treatment with 100% accuracy.

The analysis of used engine oils from industrial engines enables the study of engine wear and oil degradation in order to evaluate the necessity of oil changes. As the matrix composition of an engine oil strongly depends on its intended application, meaningful diagnostic oil analyses bear considerable challenges. Owing to the broad spectrum of available oil matrices, we have evaluated the applicability of using an internal standard and/or preceding sample digestion for elemental analysis of used engine oils via inductively coupled plasma optical emission spectroscopy (ICP OES). Elements originating from both wear particles and additives as well as particle size influence could be clearly recognized by their distinct digestion behaviour. While a precise determination of most wear elements can be achieved in oily matrix, the measurement of additives is performed preferably after sample digestion. Considering a dataset of physicochemical parameters and elemental composition for several hundred used engine oils, we have further investigated the feasibility of predicting the identity and overall condition of an unknown combustion engine using the machine learning system XGBoost. A maximum accuracy of 89.6% in predicting the engine type was achieved, a mean error of less than 10% of the observed timeframe in predicting the oil running time and even less than 4% for the total engine running time, based purely on common oil check data. Furthermore, obstacles and possibilities to improve the performance of the machine learning models were analysed and the factors that enabled the prediction were explored with SHapley Additive exPlanation (SHAP). Our results demonstrate that both the identification of an unknown engine as well as a lifetime assessment can be performed for a first estimation of the actual sample without requiring meticulous documentation.

Ghana suffers from frequent power outages, which can be compensated by off-grid energy solutions. Photovoltaic-hybrid systems become more and more important for rural electrification due to their potential to offer a clean and cost-effective energy supply. However, uncertainties related to the prediction of electrical loads and solar irradiance result in inefficient system control and can lead to an unstable electricity supply, which is vital for the high reliability required for applications within the health sector. Model predictive control (MPC) algorithms present a viable option to tackle those uncertainties compared to rule-based methods, but strongly rely on the quality of the forecasts. This study tests and evaluates (a) a seasonal autoregressive integrated moving average (SARIMA) algorithm, (b) an incremental linear regression (ILR) algorithm, (c) a long short-term memory (LSTM) model, and (d) a customized statistical approach for electrical load forecasting on real load data of a Ghanaian health facility, considering initially limited knowledge of load and pattern changes through the implementation of incremental learning. The correlation of the electrical load with exogenous variables was determined to map out possible enhancements within the algorithms. Results show that all algorithms show high accuracies with a median normalized root mean square error (nRMSE) <0.1 and differing robustness towards load-shifting events, gradients, and noise. While the SARIMA algorithm and the linear regression model show extreme error outliers of nRMSE >1, methods via the LSTM model and the customized statistical approaches perform better with a median nRMSE of 0.061 and stable error distribution with a maximum nRMSE of <0.255. The conclusion of this study is a favoring towards the LSTM model and the statistical approach, with regard to MPC applications within photovoltaic-hybrid system solutions in the Ghanaian health sector.

Background: Coniferous woods (Abies nordmanniana (Stev.) Spach, Abies procera Rehd, Picea abies (L.) H.Karst, and Picea pungens Engelm.) could contain useful secondary metabolites to produce sustainable packaging materials, e.g., by substitution of harmful petrol-based additives in plastic packaging. This study aims to characterise the antioxidant and light-absorbing properties and ingredients of different coniferous wood extracts with regard to different plant fragments and drying conditions. Furthermore, the valorisation of used Christmas trees is evaluated. Methods: Different drying and extraction techniques were applied with the extracts being characterised by determining the total phenolic content (TPC), total antioxidant capacity (TAC), and absorbance in the ultraviolet range (UV). Gas chromatography coupled with mass spectrometry (GC-MS) and an acid–butanol assay (ABA) were used to characterise the extract constituents. Results: All the extracts show a considerably high UV absorbance while interspecies differences did occur. All the fresh and some of the dried biomass extracts reached utilisable TAC and TPC values. A simplified extraction setup for industrial application is evaluated; comparable TAC results could be reached with modifications. Conclusion: Coniferous woods are a promising renewable resource for preparation of sustainable antioxidants and photostabilisers. This particularly applies to Christmas trees used for up to 12 days. After extraction, the biomass can be fully valorised by incorporation in paper packaging.

Surface-enhanced Raman spectroscopy (SERS) with subsequent chemometric evaluation was performed for the rapid and non-destructive differentiation of seven important meat-associated microorganisms, namely Brochothrix thermosphacta DSM 20171, Pseudomonas fluorescens DSM 4358, Salmonella enterica subsp. enterica sv. Enteritidis DSM 14221, Listeria monocytogenes DSM 19094, Micrococcus luteus DSM 20030, Escherichia coli HB101 and Bacillus thuringiensis sv. israelensis DSM 5724. A simple method for collecting spectra from commercial paper-based SERS substrates without any laborious pre-treatments was used. In order to prepare the spectroscopic data for classification at genera level with a subsequent chemometric evaluation consisting of principal component analysis and discriminant analysis, a pre-processing method with spike correction and sum normalisation was performed. Because of the spike correction rather than exclusion, and therefore the use of a balanced data set, the multivariate analysis of the data is significantly resilient and meaningful. The analysis showed that the differentiation of meat-associated microorganisms and thereby the detection of important meat-related pathogenic bacteria was successful on genera level and a cross-validation as well as a classification of ungrouped data showed promising results, with 99.5 % and 97.5 %, respectively.

Miscanthus crops possess very attractive properties such as high photosynthesis yield and carbon fixation rate. Because of these properties, it is currently considered for use in second-generation biorefineries. Here we analyze the differences in chemical composition between M. x giganteus, a commonly studied Miscanthus genotype, and M. nagara, which is relatively understudied but has useful properties such as increased frost resistance and higher stem stability. Samples of M. x giganteus (Gig35) and M. nagara (NagG10) have been separated by plant portion (leaves and stems) in order to isolate the corresponding lignins. The organosolv process was used for biomass pulping (80% ethanol solution, 170 °C, 15 bar). Biomass composition and lignin structure analysis were performed using composition analysis, Fourier-transform infrared (FTIR), ultraviolet-visible (UV-Vis) and nuclear magnetic resonance (NMR) spectroscopy, thermogravimetric analysis (TGA), size exclusion chromatography (SEC) and pyrolysis gas-chromatography/mass spectrometry (Py-GC/MS) to determine the 3D structure of the isolated lignins, monolignol ratio and most abundant linkages depending on genotype and harvesting season. SEC data showed significant differences in the molecular weight and polydispersity indices for stem versus leaf-derived lignins. Py-GC/MS and hetero-nuclear single quantum correlation (HSQC) NMR revealed different monolignol compositions for the two genotypes (Gig35, NagG10). The monolignol ratio is slightly influenced by the time of harvest: stem-derived lignins of M. nagara showed increasing H and decreasing G unit content over the studied harvesting period (December–April).

The number of studies on work breaks and the importance of this subject is growing rapidly, with research showing that work breaks increase employees’ wellbeing and performance and workplace safety. However, comparing the results of work break research is difficult since the study designs and methods are heterogeneous and there is no standard theoretical model for work breaks. Based on a systematic literature search, this scoping review included a total of 93 studies on experimental work break research conducted over the last 30 years. This scoping review provides a first structured evaluation regarding the underlying theoretical framework, the variables investigated, and the measurement methods applied. Studies using a combination of measurement methods from the categories “self-report measures,” “performance measures,” and “physiological measures” are most common and to be preferred in work break research. This overview supplies important information for ergonomics researchers allowing them to design work break studies with a more structured and stronger theory-based approach. A standard theoretical model for work breaks is needed in order to further increase the comparability of studies in the field of experimental work break research in the future.

Due to global ecological and economic challenges that have been correlated to the transition from fossil-based to renewable resources, fundamental studies are being performed worldwide to replace fossil fuel raw materials in plastic production. One aspect of current research is the development of lignin-derived polyols to substitute expensive fossil-based polyol components for polyurethane and polyester production. This article describes the synthesis of bioactive lignin-based polyurethane coatings using unmodified and demethylated Kraft lignins. Demethylation was performed to enhance the reaction selectivity toward polyurethane formation. The antimicrobial activity was tested according to a slightly modified standard test (JIS Z 2801:2010). Besides effects caused by the lignins themselves, triphenylmethane derivatives (brilliant green and crystal violet) were used as additional antimicrobial substances. Results showed increased antimicrobial capacity against Staphylococcus aureus. Furthermore, the coating color could be varied from dark brown to green and blue, respectively.