Refine
H-BRS Bibliography
- yes (61)
Departments, institutes and facilities
- Institut für Technik, Ressourcenschonung und Energieeffizienz (TREE) (61) (remove)
Document Type
- Article (28)
- Conference Object (25)
- Preprint (3)
- Part of a Book (2)
- Research Data (1)
- Doctoral Thesis (1)
- Part of Periodical (1)
Year of publication
- 2023 (61) (remove)
Keywords
- ENaC (2)
- Global horizontal irradiance (2)
- Lattice Boltzmann Method (2)
- Machine Learning (2)
- Quality diversity (2)
- West Africa (2)
- state of charge (2)
- (poly)saccharides (1)
- Agarose (1)
- Aloe vera (1)
Electrical signal transmission in power electronic devices takes place through high-purity aluminum bonding wires. Cyclic mechanical and thermal stresses during operation lead to fatigue loads, resulting in premature failure of the wires, which cannot be reliably predicted. The following work presents two fatigue lifetime models calibrated and validated based on experimental fatigue results of an aluminum bonding wire and subsequently transferred and applied to other wire types. The lifetime modeling of Wöhler curves for different load ratios shows good but limited applicability for the linear model. The model can only be applied above 10,000 cycles and within the investigated load range of R = 0.1 to R = 0.7. The nonlinear model shows very good agreement between model prediction and experimental results over the entire investigated cycle range. Furthermore, the predicted Smith diagram is not only consistent in the investigated load range but also in the extrapolated load range from R = −1.0 to R = 0.8. A transfer of both model approaches to other wire types by using their tensile strengths can be implemented as well, although the nonlinear model is more suitable since it covers the entire load and cycle range.
This paper presents a novel approach to address noise, vibration, and harshness (NVH) issues in electrically assisted bicycles (e-bikes) caused by the drive unit. By investigating and optimising the structural dynamics during early product development, NVH can decisively be improved and valuable resources can be saved, emphasising its significance for enhancing riding performance. The paper offers a comprehensive analysis of the e-bike drive unit’s mechanical interactions among relevant components, culminating—to the best of our knowledge—in the development of the first high-fidelity model of an entire e-bike drive unit. The proposed model uses the principles of elastic multi body dynamics (eMBD) to elucidate the structural dynamics in dynamic-transient calculations. Comparing power spectra between measured and simulated motion variables validates the chosen model assumptions. The measurements of physical samples utilise accelerometers, contactless laser Doppler vibrometry (LDV) and various test arrangements, which are replicated in simulations and provide accessibility to measure vibrations onto rotating shafts and stationary structures. In summary, this integrated system-level approach can serve as a viable starting point for comprehending and managing the NVH behaviour of e-bikes.
A company's financial documents use tables along with text to organize the data containing key performance indicators (KPIs) (such as profit and loss) and a financial quantity linked to them. The KPI’s linked quantity in a table might not be equal to the similarly described KPI's quantity in a text. Auditors take substantial time to manually audit these financial mistakes and this process is called consistency checking. As compared to existing work, this paper attempts to automate this task with the help of transformer-based models. Furthermore, for consistency checking it is essential for the table's KPIs embeddings to encode the semantic knowledge of the KPIs and the structural knowledge of the table. Therefore, this paper proposes a pipeline that uses a tabular model to get the table's KPIs embeddings. The pipeline takes input table and text KPIs, generates their embeddings, and then checks whether these KPIs are identical. The pipeline is evaluated on the financial documents in the German language and a comparative analysis of the cell embeddings' quality from the three tabular models is also presented. From the evaluation results, the experiment that used the English-translated text and table KPIs and Tabbie model to generate table KPIs’ embeddings achieved an accuracy of 72.81% on the consistency checking task, outperforming the benchmark, and other tabular models.
When optimizing the process parameters of the acidic ethanolic organosolv process, the aim is usually to maximize the delignification and/or lignin purity. However, process parameters such as temperature, time, ethanol and catalyst concentration, respectively, can also be used to vary the structural properties of the obtained organosolv lignin, including the molecular weight and the ratio of aliphatic versus phenolic hydroxyl groups, among others. This review particularly focuses on these influencing factors and establishes a trend analysis between the variation of the process parameters and the effect on lignin structure. Especially when larger data sets are available, as for process temperature and time, correlations between the distribution of depolymerization and condensation reactions are found, which allow direct conclusions on the proportion of lignin's structural features, independent of the diversity of the biomass used. The newfound insights gained from this review can be used to tailor organosolv lignins isolated for a specific application.
Trends of environmental awareness, combined with a focus on personal fitness and health, motivate many people to switch from cars and public transport to micromobility solutions, namely bicycles, electric bicycles, cargo bikes, or scooters. To accommodate urban planning for these changes, cities and communities need to know how many micromobility vehicles are on the road. In a previous work, we proposed a concept for a compact, mobile, and energy-efficient system to classify and count micromobility vehicles utilizing uncooled long-wave infrared (LWIR) image sensors and a neuromorphic co-processor. In this work, we elaborate on this concept by focusing on the feature extraction process with the goal to increase the classification accuracy. We demonstrate that even with a reduced feature list compared with our early concept, we manage to increase the detection precision to more than 90%. This is achieved by reducing the images of 160 × 120 pixels to only 12 × 18 pixels and combining them with contour moments to a feature vector of only 247 bytes.
Rosenbrock–Wanner methods for systems of stiff ordinary differential equations are well known since the seventies. They have been continuously developed and are efficient for differential-algebraic equations of index-1, as well. Their disadvantage that the Jacobian matrix has to be updated in every time step becomes more and more obsolete when automatic differentiation is used. Especially the family of Rodas methods has proven to be a standard in the Julia package DifferentialEquations. However, the fifth-order Rodas5 method undergoes order reduction for certain problem classes. Therefore, the goal of this paper is to compute a new set of coefficients for Rodas5 such that this order reduction is reduced. The procedure is similar to the derivation of the methods Rodas4P and Rodas4P2. In addition, it is possible to provide new dense output formulas for Rodas5 and the new method Rodas5P. Numerical tests show that for higher accuracy requirements Rodas5P always belongs to the best methods within the Rodas family.
A biodegradable blend of PBAT—poly(butylene adipate-co-terephthalate)—and PLA—poly(lactic acid)—for blown film extrusion was modified with four multi-functional chain extending cross-linkers (CECL). The anisotropic morphology introduced during film blowing affects the degradation processes. Given that two CECL increased the melt flow rate (MFR) of tris(2,4-di-tert-butylphenyl)phosphite (V1) and 1,3-phenylenebisoxazoline (V2) and the other two reduced it (aromatic polycarbodiimide (V3) and poly(4,4-dicyclohexylmethanecarbodiimide) (V4)), their compost (bio-)disintegration behavior was investigated. It was significantly altered with respect to the unmodified reference blend (REF). The disintegration behavior at 30 and 60 °C was investigated by determining changes in mass, Young’s moduli, tensile strengths, elongations at break and thermal properties. In order to quantify the disintegration behavior, the hole areas of blown films were evaluated after compost storage at 60 °C to calculate the kinetics of the time dependent degrees of disintegration. The kinetic model of disintegration provides two parameters: initiation time and disintegration time. They quantify the effects of the CECL on the disintegration behavior of the PBAT/PLA compound. Differential scanning calorimetry (DSC) revealed a pronounced annealing effect during storage in compost at 30 °C, as well as the occurrence of an additional step-like increase in the heat flow at 75 °C after storage at 60 °C. The disintegration consists of processes which affect amorphous and crystalline phase of PBAT in different manner that cannot be understood by a hydrolytic chain degradation only. Furthermore, gel permeation chromatography (GPC) revealed molecular degradation only at 60 °C for the REF and V1 after 7 days of compost storage. The observed losses of mass and cross-sectional area seem to be attributed more to mechanical decay than to molecular degradation for the given compost storage times.
Accurate forecasting of solar irradiance is crucial for the integration of solar energy into the power grid, power system planning, and the operation of solar power plants. The Weather Research and Forecasting (WRF) model, with its solar radiation (WRF-Solar) extension, has been used to forecast solar irradiance in various regions worldwide. However, the application of the WRF-Solar model for global horizontal irradiance (GHI) forecasting in West Africa, specifically in Ghana, has not been studied. This study aims to evaluate the performance of the WRF-Solar model for GHI forecasting in Ghana, focusing on 3 health centers (Kologo, Kumasi and Akwatia) for the year 2021. We applied a two one-way nested domain (D1=15 km and D2=3 km) to investigate the ability of the WRF solar model to forecast GHI up to 72 hours in advance under different atmospheric conditions. The initial and lateral boundary conditions were taken from the ECMWF operational forecasts. In addition, the optical aerosol depth (AOD) data at 550 nm from the Copernicus Atmosphere Monitoring Service (CAMS) were considered. The study uses statistical metrics such as mean bias error (MBE), root mean square error (RMSE), to evaluate the performance of the WRF-Solar model with the observational data obtained from automatic weather stations in the three health centers in Ghana. The results of this study will contribute to the understanding of the capabilities and limitations of the WRF-Solar model for forecasting GHI in West Africa, particularly in Ghana, and provide valuable information for stakeholders involved in solar energy generation and grid integration towards optimized management of in the region.
A Fourier scatterometry setup is evaluated to recover the key parameters of optical phase gratings. Based on these parameters, systematic errors in the printing process of two-photon polymerization (TPP) gray-scale lithography three-dimensional printers can be compensated, namely tilt and curvature deviations. The proposed setup is significantly cheaper than a confocal microscope, which is usually used to determine calibration parameters for compensation of the TPP printing process. The grating parameters recovered this way are compared to those obtained with a confocal microscope. A clear correlation between confocal and scatterometric measurements is first shown for structures containing either tilt or curvature. The correlation is also shown for structures containing a mixture of tilt and curvature errors (squared Pearson coefficient r2 = 0.92). This compensation method is demonstrated on a TPP printer: a diffractive optical element printed with correction parameters obtained from Fourier scatterometry shows a significant reduction in noise as compared to the uncompensated system. This verifies the successful reduction of tilt and curvature errors. Further improvements of the method are proposed, which may enable the measurements to become more precise than confocal measurements in the future, since scatterometry is not affected by the diffraction limit.
Estimates of global horizontal irradiance (GHI) from reanalysis and satellite-based data are the most important information for the design and monitoring of PV systems in Africa, but their quality is unknown due to the lack of in situ measurements. In this study, we evaluate the performance of hourly GHI from state-of-the-art reanalysis and satellite-based products (ERA5, CAMS, MERRA-2, and SARAH-2) with 37 quality-controlled in situ measurements from novel meteorological networks established in Burkina Faso and Ghana under different weather conditions for the year 2020. The effects of clouds and aerosols are also considered in the analysis by using common performance measures for the main quality attributes and a new overall performance value for the joint assessment. The results show that satellite data performs better than reanalysis data under different atmospheric conditions. Nevertheless, both data sources exhibit significant bias of more than 150 W/m2 in terms of RMSE under cloudy skies compared to clear skies. The new measure of overall performance clearly shows that the hourly GHI derived from CAMS and SARAH-2 could serve as viable alternative data for assessing solar energy in the different climatic zones of West Africa.